m*********3 发帖数: 158 | 1 朋友接手的项目,TI MSP430-F169(?) based embedded system. 据说整个系统在高温
和低温时会变得不稳定,具体表现是串口数据流失。我怀疑是voltage regular的问题
。 但据他讲,往板子上喷冷气的话, 一切正常。但是往TI 的Microcontroller上喷,
马上就出问题了。 我对TI不熟悉,拿上来问问同学们,帮我分析分析。 32KHZ
crystal. Is it possible the crystal became unstable? What's possible cause?
谢了先。 |
l***g 发帖数: 1035 | 2 If timing related most likely crystal drifts. Use better oscillator or slow
down.
?
【在 m*********3 的大作中提到】![](/moin_static193/solenoid/img/up.png) : 朋友接手的项目,TI MSP430-F169(?) based embedded system. 据说整个系统在高温 : 和低温时会变得不稳定,具体表现是串口数据流失。我怀疑是voltage regular的问题 : 。 但据他讲,往板子上喷冷气的话, 一切正常。但是往TI 的Microcontroller上喷, : 马上就出问题了。 我对TI不熟悉,拿上来问问同学们,帮我分析分析。 32KHZ : crystal. Is it possible the crystal became unstable? What's possible cause? : 谢了先。
|
g******u 发帖数: 3060 | |
t*******n 发帖数: 408 | 4 How high n how low?
?
【在 m*********3 的大作中提到】![](/moin_static193/solenoid/img/up.png) : 朋友接手的项目,TI MSP430-F169(?) based embedded system. 据说整个系统在高温 : 和低温时会变得不稳定,具体表现是串口数据流失。我怀疑是voltage regular的问题 : 。 但据他讲,往板子上喷冷气的话, 一切正常。但是往TI 的Microcontroller上喷, : 马上就出问题了。 我对TI不熟悉,拿上来问问同学们,帮我分析分析。 32KHZ : crystal. Is it possible the crystal became unstable? What's possible cause? : 谢了先。
|
m*********3 发帖数: 158 | 5 >Don't know the exact temp, but he said it was within the spec.
>I believe they had an external crystal oscillator. Maybe it is not the
right choice?
thanks! |
g******u 发帖数: 3060 | 6 各种问题都可能,第一步是重复这个喷冷气实验,看看各个电压是否稳定,然后就每个
重要接口都示波器看着吧。 |
i*****t 发帖数: 24265 | 7 32KHz晶振?
串口?
波特率多少?
这个晶振频率本身太低而且不是标准频率,那么会造成理论上的误码的,加
上温差变化晶振timing变化一点,就会导致误码。
?
【在 m*********3 的大作中提到】![](/moin_static193/solenoid/img/up.png) : 朋友接手的项目,TI MSP430-F169(?) based embedded system. 据说整个系统在高温 : 和低温时会变得不稳定,具体表现是串口数据流失。我怀疑是voltage regular的问题 : 。 但据他讲,往板子上喷冷气的话, 一切正常。但是往TI 的Microcontroller上喷, : 马上就出问题了。 我对TI不熟悉,拿上来问问同学们,帮我分析分析。 32KHZ : crystal. Is it possible the crystal became unstable? What's possible cause? : 谢了先。
|
m*********3 发帖数: 158 | 8
谢谢。
【在 i*****t 的大作中提到】![](/moin_static193/solenoid/img/up.png) : 32KHz晶振? : 串口? : 波特率多少? : 这个晶振频率本身太低而且不是标准频率,那么会造成理论上的误码的,加 : 上温差变化晶振timing变化一点,就会导致误码。 : : ?
|
i*****t 发帖数: 24265 | 9 可以降低波特率试试,如果好些那么就是晶振不准
【在 m*********3 的大作中提到】![](/moin_static193/solenoid/img/up.png) : : 谢谢。
|
t*******n 发帖数: 408 | 10 Crystal Osc should be better than any other internal clock sources.
【在 m*********3 的大作中提到】![](/moin_static193/solenoid/img/up.png) : >Don't know the exact temp, but he said it was within the spec. : >I believe they had an external crystal oscillator. Maybe it is not the : right choice? : thanks!
|
|
|
u*******m 发帖数: 3395 | 11 是一个板子有问题还是一批板子都有问题?先把这个搞清楚了。可以排除是板子故障还
是设计或者一批零件的问题。 |
d********g 发帖数: 11948 | 12 晶振应该是最稳的 考虑jitter因素没?
?
【在 m*********3 的大作中提到】![](/moin_static193/solenoid/img/up.png) : 朋友接手的项目,TI MSP430-F169(?) based embedded system. 据说整个系统在高温 : 和低温时会变得不稳定,具体表现是串口数据流失。我怀疑是voltage regular的问题 : 。 但据他讲,往板子上喷冷气的话, 一切正常。但是往TI 的Microcontroller上喷, : 马上就出问题了。 我对TI不熟悉,拿上来问问同学们,帮我分析分析。 32KHZ : crystal. Is it possible the crystal became unstable? What's possible cause? : 谢了先。
|
j*******1 发帖数: 2045 | 13 芯片用的是商业片还是工业级芯片
【在 d********g 的大作中提到】![](/moin_static193/solenoid/img/up.png) : 晶振应该是最稳的 考虑jitter因素没? : : ?
|
t******g 发帖数: 17520 | 14 mixed signal的controller?
不明觉厉,
如果用thermal stream往板子上吹, 能保证整个
模块在控制温度内那?如果往controller 上吹的话, 周边的
元件isolate地好吗?
我猜有可能上面说的jitter, skew, PLL
可能grounding, decoupling, 如果软件硬件没问题,
低温solder joint的问题?
如果是低能片, 这种从睡觉起床时间会不会随着温度变化?
原因可以很多。。。 |
W*****x 发帖数: 684 | 15 32768是给RTC时钟用的,你的板子用的是内部晶振。
不稳定的话,可以换成外部有源晶振。
但成本和功耗要权衡。 |
i*****t 发帖数: 24265 | 16 ,俺说32K晶振怎么能串口波特115k呢,原来是内部晶振,那当然不准了
【在 W*****x 的大作中提到】![](/moin_static193/solenoid/img/up.png) : 32768是给RTC时钟用的,你的板子用的是内部晶振。 : 不稳定的话,可以换成外部有源晶振。 : 但成本和功耗要权衡。
|
W*****x 发帖数: 684 | |