b**********y 发帖数: 7371 | 1 Looking to refurbish my old AR, which has a mid-length flattop upper, with
standard handguard and A2 gas block. Did some research and looks the most
hassle-free free-floating solution is the Vltor CASV-MX handguard with rails
. Has any gurus here used it?
2 concerns: 1st is the raised top on the upper after installation, will it
still work with my red-dot; 2nd is how to take off the sling swirl attached
to the A2 block.
TIA |
b*****e 发帖数: 5133 | 2 想不出红点为什么不能再用,absolute和1/3 co-witness应该都不影响啊。
用比sling swivel上铆钉头小一号的punch顺着铆钉安装反方向用榔头敲就应该可以把
sling swivel取下了。先用dremel把铆钉头小心切掉点再敲更容易。再不济dremel直接
锯掉sling swivel就是了。
装上CASV(或大部分其它导轨)枪会重不少,真需要导轨吗?有那么多东西要往导轨上放
吗?还是就要个不同的样子。 |
b**********y 发帖数: 7371 | 3 Thx for the info. I will give it a try
The std handguard has a little play in it when shooting - I used to shoot
22LR in this AR, which is hardly noticed; but for 5.56 rounds the handguard
actually moves quite abit, which is annoying now. That's the main reason. So
looking for a free-float, but requires no gunsmith.
Certainly I wudn't complain abt the look, comparing to the std HG. |
j***n 发帖数: 3786 | |
b*****e 发帖数: 5133 | 5 导轨其实大家能好好用上的不多,像SCAR那样顶部全导轨,3/6/9一小段导轨能满足绝
大部分人的要求,包括不少当兵的,还能省些份量下来。这些背在身上晃荡的份量越小
越好,时间越长感觉越明显。
楼主要导轨一是要好看另外一个是觉得现在护木松动很烦。
【在 j***n 的大作中提到】 : 这个导轨好像18oz吧,很重
|
b**********y 发帖数: 7371 | 6 俺只打算用这个护木,下面装个VFG,不装其他的导轨,大概15Oz
俺的DD 12“ OMEGA 护木也是15Oz左右, 是不轻啊
【在 j***n 的大作中提到】 : 这个导轨好像18oz吧,很重
|
b**********y 发帖数: 7371 | 7 其实哈,介CASV护木是跟SCAR的满想的,不需要的RAIL可不装
俺google的结果,这大概是仅有的不要换BARREL NUTS的FREE-FLOATING护木
枪的部件西里咣啷让人很不爽,尤其是护木和枪托
【在 b*****e 的大作中提到】 : 导轨其实大家能好好用上的不多,像SCAR那样顶部全导轨,3/6/9一小段导轨能满足绝 : 大部分人的要求,包括不少当兵的,还能省些份量下来。这些背在身上晃荡的份量越小 : 越好,时间越长感觉越明显。 : 楼主要导轨一是要好看另外一个是觉得现在护木松动很烦。
|