x*7 发帖数: 11281 | |
t*****8 发帖数: 1274 | 2 现在classic arms卖499。。。这个group buy能搞到多少?如果能回到以前300多的时
候,我立刻跳一把。。。 |
f****a 发帖数: 4708 | |
x*7 发帖数: 11281 | 4 最近saiga的7.62和223都降价了,估计这个也快了吧
【在 t*****8 的大作中提到】![](/moin_static193/solenoid/img/up.png) : 现在classic arms卖499。。。这个group buy能搞到多少?如果能回到以前300多的时 : 候,我立刻跳一把。。。
|
x*7 发帖数: 11281 | 5 换管子,没研究过,为什么要换呀?
【在 f****a 的大作中提到】![](/moin_static193/solenoid/img/up.png) : saiga12能换枪管麽?容易麽?
|
T******g 发帖数: 21328 | |
f****a 发帖数: 4708 | 7 当地有个靶场对shotgun的要求是枪管>26"。
研究一下Saiga的枪管好换不。
【在 x*7 的大作中提到】![](/moin_static193/solenoid/img/up.png) : 换管子,没研究过,为什么要换呀?
|
S**********s 发帖数: 4534 | 8
not easy, not recommended, and not a good idea.
but if you insist, here is an example of saiga 12 barrel removal:
"I just removed my barrel the other night. I removed the pin, and then drove
it out of the reciever by placing a block of teflon cutting board material
against the reciever and smacking it with a hammer. I alternated from one
side of the reciever to the other. I took my time and it came off no problem
. I removed it to get the barrell cut down and a hybird muzzle break/flash
hider permanently installed for an overall length of 18". I'm thinking that
what's going to be fun is getting the barrell pressed back in clocked
correctly for the pin to go back in."
also note that there are VERY FEW replacement saiga 12 barrels on the market.
【在 f****a 的大作中提到】![](/moin_static193/solenoid/img/up.png) : saiga12能换枪管麽?容易麽?
|
T*R 发帖数: 25894 | 9 卖300多,毛子也不能答应吧。
【在 t*****8 的大作中提到】![](/moin_static193/solenoid/img/up.png) : 现在classic arms卖499。。。这个group buy能搞到多少?如果能回到以前300多的时 : 候,我立刻跳一把。。。
|
t******8 发帖数: 2803 | 10 Ruger 10/22 枪管都没拆成功的飘过。。
drove
material
problem
that
【在 S**********s 的大作中提到】![](/moin_static193/solenoid/img/up.png) : : not easy, not recommended, and not a good idea. : but if you insist, here is an example of saiga 12 barrel removal: : "I just removed my barrel the other night. I removed the pin, and then drove : it out of the reciever by placing a block of teflon cutting board material : against the reciever and smacking it with a hammer. I alternated from one : side of the reciever to the other. I took my time and it came off no problem : . I removed it to get the barrell cut down and a hybird muzzle break/flash : hider permanently installed for an overall length of 18". I'm thinking that : what's going to be fun is getting the barrell pressed back in clocked
|