p**e
发帖数: 533 | 1 前一阵在costco买了watts premier净水器(WP-5 WP5-50 KP-5 RO-5M)，然后也在amazon买了一
个permeate pump。
我试着在网上找装permeate pump的manual，但是只是找到了如何安装pump到
freshwatersystems的净水器http://www.freshwatersystems.com/t-reverseosmosispermeatepump.aspx，但是
它们的结构有点不一样。不知道哪里有安装permeate
pump到 watts premier净水器的manual？
如果有谁安装过，包子求经验。谢谢。
我现在主要有以下问题（这些都是阅读manual和网上搜索后还有的问题）：
1. 我从amazon买的pump只有一个pump，不是kit，需不需要买额外的配件？如果要，都是些什么
以及在哪里买？
2. 净水器上有六个口。 Faucet, TAP, Tank, Drain都有管子连着。另外两个口是zero
waste auxiliary ports好像都没有开口。这两个口有用吗？
3. Pump上有Permeate In, Permeate Out, Brine In, Brine Out 四个口，这四个口怎
么跟净水器连？
4. 如果装了pump，还须不需要跟drain相连？
5. zero waste的pump是不是跟这个permeate pump不一样？
6. 净水器包装袋里跟final polishing filter一个包装袋的那个最大的part(白色塑料两头是圆圈)是什么？干什么用？
7. 净水器final polishing filter应该固定在哪里？
谢谢了。也希望我的问题和得到的答案能帮助更多的人。 | p**e
发帖数: 533 | 2 经过研究，我figure out了。后来也给watts premier 打电话要到了manual。
现在贴在这儿，以方便跟我一样的朋友。
谢谢大家
amazon买了一
都是些什么
【在 p**e 的大作中提到】
: 前一阵在costco买了watts premier净水器(WP-5 WP5-50 KP-5 RO-5M)，然后也在amazon买了一
: 个permeate pump。
: 我试着在网上找装permeate pump的manual，但是只是找到了如何安装pump到
: freshwatersystems的净水器http://www.freshwatersystems.com/t-reverseosmosispermeatepump.aspx，但是
: 它们的结构有点不一样。不知道哪里有安装permeate
: pump到 watts premier净水器的manual？
: 如果有谁安装过，包子求经验。谢谢。
: 我现在主要有以下问题（这些都是阅读manual和网上搜索后还有的问题）：
: 1. 我从amazon买的pump只有一个pump，不是kit，需不需要买额外的配件？如果要，都是些什么
: 以及在哪里买？
| p**e
发帖数: 533 | 3 好像长传不了超过1M的附件。以下是需要的parts和步骤：
Parts Needed:
• (1) Permeate Pump with mounting clip (P/N 152002)
• (2) Quick Connect Reducer Union (P/N 125037)
• (2) 3” long, 1/4” Blue tubes (P/N 710450)
• (1) 48” long, 1/4” blue tube (P/N 610113)
• (1) 3/8” Quick Connect Union Tee (P/N 225051)
• (1) 3/8” Plug Insert (P/N 164027)
NOTE: The Permeate Pump is equipped with ¼” Quick Connect push-to-
connect fittings.
The pump can be used in RO systems with 3/8” tubing by inserting a short
piece of 1/4”
tubing into the port on the Permeate Pump and attaching a Quick Connect
Reducer Union
to the tubing. Also, when mounting the Permeate Pump, make sure the outlet
ports of the
Permeate Pump are above the inlet ports in order to allow entrapped air to
escape
Installation Steps:
1. Turn off the incoming water to the reverse osmosis unit. Lift the handle
on the reverse
osmosis drinking water faucet to drain the water from the system and storage
tank.
Note: If tank is equipped with a ball valve, close valve to preserve the
tank water.
2. Before installing the Permeate Pump, remove the blue tube-inserts from
the ports.
Refer to the diagram on Page 2 for instructions for disconnecting from a
quick-connect
fitting.
3. Remove the 3/8” blue tube from the manifold “TANK” port and insert the
3/8” Plug
4. Locate the 3/8” blue tube from the manifold “FAUCET” port and cut
approximately 24”
from the manifold and re-route into the Permeate Pump “PERMEATE IN” port
using a
Reducer Union and a 3” long, 1/4” blue tube
5. Insert the 3/8” blue tube from the faucet into the Permeate Pump “
PERMEATE OUT”
port using a Reducer Union and a 3” long, 1/4” blue tube
6. Locate the 3/8” blue tube between the faucet and Permeate Pump, and then
cut and
insert the 3/8” Union Tee.
7. Insert the 3/8” blue tube leading to the tank into the open port of the
3/8” Union Tee
8. Locate the 1/4” red tube between the manifold “DRAIN” port and the
faucet air gap
inlet and then cut the tube 24” from the manifold (Making sure to leave the
flow
restrictor plugged into the manifold) Insert the red tube from the manifold
into the
Permeate Pump “BRINE IN” port and the red tube from the faucet into the
Permeate
Pump “BRINE OUT” port.
9. Make sure your installation matches the diagram shown in Figure 2
10. Turn on the water supply. Check for leaks periodically for the next 24-
48 hours as the
system fills and again after it shuts off when the tanks is full
【在 p**e 的大作中提到】
: 经过研究，我figure out了。后来也给watts premier 打电话要到了manual。
: 现在贴在这儿，以方便跟我一样的朋友。
: 谢谢大家
:
: amazon买了一
: 都是些什么
|
|
