g*******y 发帖数: 2783 | 1 点编辑不小心把自己的帖子给删掉了...
大概情况就是water heater附近的那个出水管和进水管了
第一张图上应该能看到我打的补丁,不过最近又开始漏了,所以准备换掉一截
第二张是热水器的管子的部分图,从热水器出来和进去的一段管子是铜的,然后就全是
塑料管子了,看颜色应该就是所谓的cpvc | i***e 发帖数: 9429 | 2 到还没见过WT用CPVC连接的,那个直角漏应该很容易修的。
楼主能不能在上个从后面方向照得图,想看看它是怎么连接的,第二张图看不清楚,
好像从进和出1尺半的位置都是铜管.你说的另外一个漏在那儿,是否可画个圈出来。 | g*******y 发帖数: 2783 | 3 明天吧,
漏水的地方就是第一个图中的两个直角弯,一个打补丁了,一个不知道为啥最近刚开始
连热水器的进出的都是铜管,然后通过fittings连了pcv的管子
【在 i***e 的大作中提到】 : 到还没见过WT用CPVC连接的,那个直角漏应该很容易修的。 : 楼主能不能在上个从后面方向照得图,想看看它是怎么连接的,第二张图看不清楚, : 好像从进和出1尺半的位置都是铜管.你说的另外一个漏在那儿,是否可画个圈出来。
| i***e 发帖数: 9429 | 4
不用图了,你说的和我估计的一样,因为没看到过,很有兴趣想知道个究竟。谢谢你。
后来去看了我们当地的Plumbing Code 和 IPC, CPVC 的确可当 热水管用,正好看到
一段怎么连接,你可以参考一下。相信我们大家都没什么经验,这管子里是有水压的,
做的要仔细点。注意看605.16.2.
D 2846/D 2846M—99 Specification for Chlorinated Poly (Vinyl Chloride) (CPVC
) Plastic Hot and Cold Water Distribution Systems . . . . . . Table 605.3,
Table 605.4, 605.16.2
B137.6—99 CPVC Pipe, Tubing and Fittings for Hot and Cold Water
Distribution Systems—with Revisions through May 1986 . . . . . . . Table
605.3, Table 605.4
605.16 CPVC plastic. Joints between CPVC plastic pipe or fittings shall
comply with Sections 605.16.1 through 605.16.3.
605.16.1 Mechanical joints. Mechanical joints shall be
installed in accordance with the manufacturer’s instructions.
605.16.2 Solvent cementing. Joint surfaces shall be clean and free from
moisture, and an approved primer shall be applied. Solvent cement, orange in
color and conforming
to ASTM F 493, shall be applied to all joint surfaces. The
joint shall be made while the cement is wet, and in accordance with ASTM D
2846 or ASTM F 493. Solvent-cement joints shall be permitted above or below
ground.
Exception:Aprimer is not required where all of the following
conditions apply:
1. The solvent cement used is third-party certified as conforming to ASTM F
493.
2. The solvent cement used is yellow in color.
3. The solvent cement is used only for joining ½ inch(12.7 mm)
through 2 inch (51 mm) diameter CPVC pipe and fittings.
4. The CPVC pipe and fittings are manufactured in accordance with ASTM D
2846.
【在 g*******y 的大作中提到】 : 明天吧, : 漏水的地方就是第一个图中的两个直角弯,一个打补丁了,一个不知道为啥最近刚开始 : 连热水器的进出的都是铜管,然后通过fittings连了pcv的管子
| g*******y 发帖数: 2783 | 5 多谢了
CPVC
【在 i***e 的大作中提到】 : : 不用图了,你说的和我估计的一样,因为没看到过,很有兴趣想知道个究竟。谢谢你。 : 后来去看了我们当地的Plumbing Code 和 IPC, CPVC 的确可当 热水管用,正好看到 : 一段怎么连接,你可以参考一下。相信我们大家都没什么经验,这管子里是有水压的, : 做的要仔细点。注意看605.16.2. : D 2846/D 2846M—99 Specification for Chlorinated Poly (Vinyl Chloride) (CPVC : ) Plastic Hot and Cold Water Distribution Systems . . . . . . Table 605.3, : Table 605.4, 605.16.2 : B137.6—99 CPVC Pipe, Tubing and Fittings for Hot and Cold Water : Distribution Systems—with Revisions through May 1986 . . . . . . . Table
|
|