t***u
发帖数: 368 | 1 买了个新的linksys router，刷了最新的DD-WRT， 结果router 彻底没有反映了，192.
168.1.1 不能连接，什么都不work了，各位达人可有建议？
感谢先 |
r*****8
发帖数: 2697 | 2 试试192.168.0.1
还是转到hardware去问吧, 那边一推牛人
192.
【在 t***u 的大作中提到】
: 买了个新的linksys router，刷了最新的DD-WRT， 结果router 彻底没有反映了，192.
: 168.1.1 不能连接，什么都不work了，各位达人可有建议？
: 感谢先
|
l*********o
发帖数: 3091 | 3 try 192.168.2.1
192.
【在 t***u 的大作中提到】
: 买了个新的linksys router，刷了最新的DD-WRT， 结果router 彻底没有反映了，192.
: 168.1.1 不能连接，什么都不work了，各位达人可有建议？
: 感谢先
|
T*****g
发帖数: 1434 | 4 The 30-30-30 Hard Reset Rule for Routers
Essentially all broadband routers used for home networking provide a reset
switch, often a very small, recessed button on the back of the unit. This
button allows you to override the current state of the device and restore it
to the default settings it had when it was first manufactured.
Some people don't realize that pressing a router's reset button for just a
second or two may do nothing. Depending on the type of router and its
current state (including the nature of any problems it may have), you may
need to hold down the button longer. Networking enthusiasts have developed
this so-called 30-30-30 hard reset procedure that should fully reset any
home router to its default settings at any time. Follow these steps to
perform a router hard reset:
1. when the unit is powered on, hold down its reset button for 30 seconds
2. while still holding down the reset button, unplug the router from power
and hold for an additional 30 seconds
3. still holding down the reset button, turn on power to the router again
and hold for 30 more seconds
After this process (a total of 90 seconds) is complete, your router should
be restored to its factory default state. Note that your particular router
may not require the full 30-30-30 procedure. For example, some routers can
at times be hard reset after only 10 seconds and without power cycling.
Nevertheless, I still recommended memorizing this 30-30-30 rule as a general
guideline. |
j*****z
发帖数: 5306 | 5 你刷的什么版本ddwrt?很多mod我知道都是静态IP,你笔记本设为自动获取是连不上的。
192.
【在 t***u 的大作中提到】
: 买了个新的linksys router，刷了最新的DD-WRT， 结果router 彻底没有反映了，192.
: 168.1.1 不能连接，什么都不work了，各位达人可有建议？
: 感谢先
|
t***u
发帖数: 368 | 6 感谢各位答复，我的router是 E2500， 刚才又接电试了一下，居然莫名其妙地恢复工
作，地址还是192.168.1.1, firmware 已经刷新成DD-WRT, 一切OK！
【在 l*********o 的大作中提到】
: try 192.168.2.1
:
: 192.
|
A******D
发帖数: 2844 | 7 刷好以后一般要30/30/30操作
【在 t***u 的大作中提到】
: 感谢各位答复，我的router是 E2500， 刚才又接电试了一下，居然莫名其妙地恢复工
: 作，地址还是192.168.1.1, firmware 已经刷新成DD-WRT, 一切OK！
|
