|
|
w********r
发帖数: 8704 | 3 你好像是用wood screw固定，然后上漆，我screw和防水胶都用了，准备上penetrating
oil/sealant,里面再铺PE liner,这样防水会不会有用？另外你有一个花盆放在半阴的
地方变形小，我这个也是在比较阴凉的位置，草莓叶子垂在周围也会挡一些光。 |
|
S*******r
发帖数: 11017 | 4 不切旧墙的drywall 用stud finder找到旧墙的stud
直接钉新的frame可以吗？
如果可以直接钉的话
那么切drywall的唯一好处就是布线对不对？
drywall不是用screw钉在stud上吗？
那岂不是要找到每一颗screw把它们一一转下来
这样切完以后才能整块卸下来？ |
|
S*******r
发帖数: 11017 | 5 不切旧墙的drywall 用stud finder找到旧墙的stud
直接钉新的frame可以吗？
如果可以直接钉的话
那么切drywall的唯一好处就是布线对不对？
drywall不是用screw钉在stud上吗？
那岂不是要找到每一颗screw把它们一一转下来
这样切完以后才能整块卸下来？ |
|
t***z
发帖数: 5112 | 6 anchor screw
不过我家的都是钉到stub上的。你弄到墙上即使用anchor screw的话结实么？孩子的破
坏力不能小看阿。。。 |
|
b***p
发帖数: 1398 | 7 agree,
I broke two screws there, don't know how to fix it now;
on the dry wall side, I inserted something like a plastic liner first, then
put the screw in |
|
b***p
发帖数: 1398 | 8 agree,
I broke two screws there, don't know how to fix it now;
on the dry wall side, I inserted something like a plastic liner first, then
put the screw in |
|
c*******t
发帖数: 953 | 9 楼主，你犯的错误太多了，一一例举如下：
1.钉子用错了。仔细观察观察你买的"wood screw"，断开的地方有没有预先做好断口？
这种不能买，这种就是假定你拧进去后要故意折断的，一生一世不再需要起出。
2.Oak的楼梯木头，需要用电动钻头先打眼，直径稍微比你的螺丝小一点。
3.墙肯定是dry wall；你需要找到stud(木头)；到HD去买stud finder。找到后，用木
螺丝上你的baby gate。墙里面的木头比较软，可以直接用screw，也可以预打眼。
4.如果一定要安在没有 stud的地方，也要用那种塑料膨胀螺丝。还是建议安装在木头
stud上面，baby gate为了是保护baby的，如果他大力去推那gate，一旦门脱开那可是
大事故。 |
|
h********8
发帖数: 7355 | 10 无绳的？电钻功率不够？换有绳的试试。十字screw bit是尖的？换个跟screw匹配的。 |
|
R********r
发帖数: 3415 | 11 怕什么，外面硅胶一封；而且你推荐的这个说：screw option
Quick easy installation: No Tools Required. Installs in minutes with two way
tape and silicone or screw option (included) on any tile, marble, plastic
or other wall surface. |
|
p**5
发帖数: 2544 | 12 thanks.
I just wacthed youtube "how to", and it seems they only put "ONE" screw on
each stud. Is that enough? I thought one has to put several screws on put a
single cabinet to the stud |
|
|
B******y
发帖数: 9065 | 14 hole太小了，深度应该不够，如果你都把十字磨平了还没有订进去的话。 |
|
d**********0
发帖数: 13081 | 15 养鸡场的当当当表示， 用makita 的 18伏 两件套 没有任何压力。 |
|
d********a
发帖数: 9567 | 16
这个问题是关于钉子的啊。
同意上边意见，重要部分先钻眼开路。 |
|
w********r
发帖数: 8704 | 17 #10螺钉的话，普通drill先钻pilot hole，impact driver直接上 |
|
|
k*******i
发帖数: 383 | 19 去考个license改行干冷暖工吧。绝对能挣更多的钱。不信请看下面的故事。
The Professor and the Plumber
One professor of mathematics noticed that his kitchen sink at his home broke
down. He called a plumber. The plumber came on the next day, sealed a few
screws and everything was working as before. The professor was delighted .
However, when the plumber gave him the bill a minute later, he was shocked.
"This is one third of my monthly salary!" he yelled. Well, all the same he
paid it and then the plumber said to him: "I understand... 阅读全帖 |
|
J****n
发帖数: 937 | 20 You'll need to work from the back of the phone, first remove any SD card,
battery, then remove the screw to lift the main board, so you can remove the
LCD unit. You might need special tools depend on the type of screw used in
the phone.
I would suggest you search for an instruction video on YouTube.
BTW, how did you know your LCD is broken? is it cracked? |
|
L**P
发帖数: 3792 | 21 众说纷纭,以下总结不知道到底如何,请牛人补充信息
步骤1: sheet metal screw or not?
Yes / No
步骤2: mastic sealant(paint) or not
Yes / No
步骤3: tape or not?
Yes / No
问题4: what tape?
A. usual duct tape (not recommended)
B. AC grade duct tape (brand model# link?)
C. Mastic tape (brand mode# link?)
D. Aluminum foil tape (HD Aluminum Foil Tape Model # 3220020500 Store SKU #
915245)
E. 3M silver tape (brand mode# link?)
功能上要考虑到两方面,固定和密封
耐力上要考虑高温低温长期
目前已知最保险方法是 Yes / Yes / Yes / D
或者Yes / Yes / Yes / B or C or E (但是hd找不到这3个传说中的产品或者... 阅读全帖 |
|
|
|
r*********s
发帖数: 2157 | 24 我也是Sear清仓买得screws，买了好几千，screw用得太快了
那个大夹子我也有， 很方便， 不过作用可以用其他东西取代，不是必须得 |
|
|
F***Q
发帖数: 6599 | 26
any screw, as long as it can fit in the old threads (or slightly larger to
create new threads when you "tap" in). if course, the screw has to be long
enough to lock the metal keys, but not too long or sticks out. |
|
c****m
发帖数: 855 | 27 胶水强度购吗。。。用来当凳子的腿。。左摇右晃的。。很坚固吗
不想用screw。。看Jordan卖的什么screw都没有呢。。也许是glue的吧 |
|
w******u
发帖数: 5413 | 28 screw gun？
dry wall screw？ |
|
w********r
发帖数: 8704 | 29 6。封口，先上一块木板，用drywall screw上紧，偶也抹了construction glue
7。上drywall，拧drywall screw
8。上drywall compound
9。上touch up paint，两遍，done。 |
|
d**********0
发帖数: 13081 | 30 好， 买了
做楼梯扶手。
Safety First 42 in. x 1-1/2 in. Concealed Screw Grab Bar in Stainless Steel
把浴室挂毛巾的换成这个。
Pegasus Antique Rope 24 in. x 4-1/2 in. Concealed Screw Grab Bar in Brushed
Nickel |
|
|
y***j
发帖数: 11235 | 32 Cost
Metal framing studs typically cost less than wood studs. This cost
savings is somewhat mitigated by the cost of electrical boxes, plastic wire
grommets, screws and moldings.
Convenience
Metal framing studs are more convenient than wood studs because they
are lighter and easier to transport. Also, using metal studs eliminates
messy sawdust piles during cutting.
Strength
Lack of strength is a major disadvantage of metal framing studs.
They can only be used ... 阅读全帖 |
|
L**P
发帖数: 3792 | 33 四大功能
1 可以推着自由移动
2 可以垂直投到天花板，主要用途
3 可以平行投到墙
4 可以调整上下1到3feet的高度
材料很简单，
2-3根1x4x8的furring strip
dry wall screw 若干
kreg jig 和 screw若干
木工胶水一点点，没多用
从ikea搞了2个带塑料头的螺丝，和固定螺母
轮子4个，5刀不到
工具需要jig saw，miter saw and/or circular saw, drill/driver, drill bits,
wood boring spades, ruler, square |
|
s***g
发帖数: 495 | 34 可不用clamp，只用screw先接butt joint with glue。
等glue干后，取screw、打孔、上dowel。 |
|
|
w*****g
发帖数: 152 | 36 If for the small hole to hold screws, Lowes/HD have both special drill and
screws kits. It takes a little long but very easy(several minutes for one
hold).
If too many holds, hammer drill will be much faster.But hammer drill will be
much more expensive. |
|
n***s
发帖数: 10056 | 37 That's not by kids. It's road hazards. My tire got that kind of screws three
times on the roads in the past ten years. If you pay attention while
driving, you can feel when the tire gets screwed. |
|
b**m
发帖数: 1466 | 38
尽量找stud,如果没有stud要用专门的drywall anchor。
一般要，要不也拧不进去。有的螺丝是不需要的。
塑料anchor的有好多种，如果是圆柱那种一般都是给混凝土或水泥用的，butterfly
anchor可以给drywall 用。
我觉得都可以。wood screw有一段是没有丝的，如果东西比较厚应该用wood screw. |
|
t****t
发帖数: 610 | 39 但是总比长mold好。修总是可以修的。
steel stud不可以用钉子，screws only.不想predrill pilot hole,可以用self
drilling screws,很方便。 |
|
p**********g
发帖数: 9558 | 40 你觉得这个如何？
http://www.lowes.com/pd_222457-10477-8+FT+GARAGE+DOOR+INS_0_?pr
附带一个来自san diego的review
Not as easy to install as some say. I struggled with the first two panels.
Trying to flex an almost four foot width of this stuff and slip it into
place took two people. I couldn't do it by myself. So I changed tactics for
the rest of the double-wide garage door. At each panel thereafter, I backed
out the hinge screws, cut a 1 3/4 inch of foam and slipped that into the 2
inch channel. Re-installed scr... 阅读全帖 |
|
l****m
发帖数: 1294 | 41 昨天在home depot买的screw，是1/4的head，长是1/2的，这个screw可以用吧？ |
|
s*****6
发帖数: 499 | 42 第一次买房，不懂啊。列出主要问题，大家帮忙看看吧
ROOF SYSTEM
Action Needed- Flashing is improperly installed at left side of chimney.
Step flashing is not under siding as required. Have aqualified roofing
contractor repair.
GARAGE / CARPORT
GARAGE DOOR HARDWARE:
Action Needed- Installing of a safety cable through the safety springs is
recommended. Safety cables are recommended to be installed through (in the
center of) the safety springs to prevent the spring from "flying" in the
event of breakage.
DOOR OPENERS(S):
Act... 阅读全帖 |
|
y***j
发帖数: 11235 | 43 wood screw, drywall screw主要用这两种，大家争论不休。
kreg jig就用kreg jig配的螺丝 |
|
T**9
发帖数: 1528 | 44 没有plan,自己乱搞的，呵呵. size 72"x32", 根据以前剩的plywood 来决定的。这个
size放整块4'x8'也可以.
桌子很简单的，桌面是3/4 MDF screwed to 3/4 Plywood，这个可以经常换;and
plywood screwed to a box frame with 2x6 for perimeter member and 2x4 for
cross member; 2x4 legs are bolted to 2x6 using 3/8" bolts with washers. One
cross member at the bottom
那些tracks 是后装的。 留的overhang 正好装Kreg clamp tracks, Festool side
tracks. |
|
r*********s
发帖数: 2157 | 45 screw 可以钻出来， 拆开搬。 再安装的时候再screw到什么地方？ 原地方会比较松动 |
|
|
|
t********t
发帖数: 5415 | 48 另外问一下，pocket hole screw只要长度/head直径对，没必要非得买kreg自己的吧？
手里还剩一堆6# 1-1/4的wood screw，看kreg建议join两块3/4应该用1-1/4，想利用一
下现有材料 |
|
c**a
发帖数: 128 | 49 看到有人提到走在二楼的地毯上，下面地板发出噪音。我刚学习并且解决了几处发响声
的地方。
我参考了该视频（http://www.youtube.com/watch?v=u9rzcumpPM0）。视频上的方法简单，请配备他要求的工具，尤其是(1) grove joint plier，一种歪头钳子，是拧断螺丝头部的必备工具，不能用普通的直头钳子。（2）应该使用3寸drywall screws，而不是desk screws，后者更粗，更难把螺丝头部拧断。
我发现他介绍的使用细铁丝探测下部木梁的方法不是很好用，我自己是不断踩，听声音
，再试着下螺钉，最后综合判断出下面木梁的走向和位置。如果位置不对，就把螺钉拧
出。下钉以后，位置对不对，很容易判断的。如果噪音区域是狭长的长方形，那么走向
和位置就很容易确定。如果噪音区是比较大片的偏正方形区域，我就只能多下钉试试。 |
|
k**l
发帖数: 2966 | 50 that is what I use to build my deck
porter cable 18V, with 2 batteries, one hour charger
though I did have another $20 corded drill just to make screwing faster (one
drill hole, the other put in screw) |
|
