a******n
发帖数: 98 | 1 Has anyone incorporated Solidworks geometry into ANSYS workbench for finite
element analysis?
Thanks a lot! |
l*****2
发帖数: 93 | |
a***8
发帖数: 2433 | 3 Yes, what you want to know? |
f*u
发帖数: 3 | 4 Sure you can
finite
【在 a******n 的大作中提到】
: Has anyone incorporated Solidworks geometry into ANSYS workbench for finite
: element analysis?
: Thanks a lot!
|
a******n
发帖数: 98 | 5 Thank you for the reply.
I want to know that if I can directly use the 3D Solidworks file ( *.sldprt,
*.sldasm) in the ANSYS workbench to perform the FE analysis. As you know,
it is difficult to draw complex geometry in ANSYS without the Designexplorer
of workbench.
I transferred Solidwork 3D file to IGES file. There are some problems of
surface generation in ANSYS.
Thanks again.
【在 a***8 的大作中提到】
: Yes, what you want to know?
|
c*********5
发帖数: 5813 | 6 you can try cosmoswork, it's an addon of solidworks purely for FEA
sldprt,
Designexplorer
【在 a******n 的大作中提到】
: Thank you for the reply.
: I want to know that if I can directly use the 3D Solidworks file ( *.sldprt,
: *.sldasm) in the ANSYS workbench to perform the FE analysis. As you know,
: it is difficult to draw complex geometry in ANSYS without the Designexplorer
: of workbench.
: I transferred Solidwork 3D file to IGES file. There are some problems of
: surface generation in ANSYS.
: Thanks again.
|
U***u
发帖数: 334 | 7 Good luck, Lin.
Also, there is a research engineer position in OH, see the article in this
ME board. Try it! |
a******n
发帖数: 98 | 8 Thanks for the reply.
I have comsmoswork, but the FEA functions are very limited.
【在 c*********5 的大作中提到】
: you can try cosmoswork, it's an addon of solidworks purely for FEA
:
: sldprt,
: Designexplorer
|
a******n
发帖数: 98 | 9 Thank you for the information. Nice to meet you here.
Wish you good luck too.
【在 U***u 的大作中提到】
: Good luck, Lin.
: Also, there is a research engineer position in OH, see the article in this
: ME board. Try it!
|
a***8
发帖数: 2433 | 10 You need the license of SolidWork/Workbench Interface, that will do exactly
what you want. |
u*****e
发帖数: 16 | 11 You can try *.sat or *.igs. I used *.sat to transfer drawing from AutoCAD to
ANSYS.
finite
【在 a******n 的大作中提到】
: Has anyone incorporated Solidworks geometry into ANSYS workbench for finite
: element analysis?
: Thanks a lot!
|
a******n
发帖数: 98 | 12 Thanks for the reply.
Parasolid and IGES files transfered from Solidworks are different from the
original file, and it also depends on the way you drew in Solidwork. ANSYS
workbench might be better.
to
【在 u*****e 的大作中提到】
: You can try *.sat or *.igs. I used *.sat to transfer drawing from AutoCAD to
: ANSYS.
:
: finite
|
